Catalogo ER International Cleantech ENG

SAVE OFFLINE

2

INDEX ER International Catalog -Electric Mobility.

pag. 4-17

-PV Devices.

pag. 18-22

-PV Structures.

pag. 23-26

-Water Treatment Products.

pag. 27-32

-Water Pumps and Generators.

pag. 33-37

-PV products.

pag. 38-46

-Wind Power products

pag. 47-49

-Geothermal Products.

pag. 50-52

-Biomass Products.

pag. 53-56

-Public Lighting

pag. 57-61

-Cleantech Incubator powered by Restart Italia.

pag. 63-65

3

ELECTRIC MOBILITY

4

IM GREEN VEHICLES COMPANY PRESENTATION

Focused on innovation, I’M Green vehicles is a company which supplys 100% electric vehicles and charging stations. Full electric, Range Extended and Bi-Modal vehicles are the vehicles that the company I’M Green Vehicles provides.

FULL ELECTRIC

FE

RANGE EXTENDED

BI-MODALE

RE

BM

5

BI-MODAL Kit Presentation The Bi-Modal technology is a system that is installed on vehicles by the I’M Green Vehicles technicians. With a rear-wheel drive vehicle which has an internal combustion engine placed on the front, the Bi-Modal kit will be insatlled by: - Keeping the original internal combustion engine without removing it. - Installing an electric engine which will allow the user to drive on a emission free base and when needed by using the internal combustion engine. - A small battery pack will be installed which will allow the user to drive for 50/60km with the Full electric engine. The Bimodal Kit can be installed on any vehicle on the market. This process will allow the user to have a divalent product, usefull for long journeys and for restricted traffic limitation areas where vehicles with the only internal combustion engine cannot drive. - OPTIONAL: It is possible to apply a new internal combustion engine which will make sure that the batteries will be recharged during the journey without using completly the full electric engine.

BM

Jolly 2000, Bruxelles Airport

6

Full Electric Kit Presentation The Full Electric kit will allow the user to ride around 100-120 km using just the electric engine without the need of a internal combustion engine. - The Full Electric kit can be disassembled and assembled on another vehicle if needed, in case if the previous vehicle with the Full Electric kit has reached it’s life. - Using an electric vehicle reduces car speed accidents by 80%. - The user of an electric vehicle has the advantage to save up to 50% on car insurance. The vehicle work maintenace is reduced up to 70%. - The Full Electric Kit gets rid of CO2 emissions like PM10 and PM2,5 in the atmosphere. - The Full Electric vehicles get rid of noise pollution.

FE

Ducato Minibus per Comune Sant’Agata di Puglia

7

Range Extended Vehicles are vehicles with both electric and nternal combustion engine which can be powered by diesel or gasoline. The internal combustion engine is only used when the lithium battery, which runs theee electric engine, needs to be charged. These vehicles are electric vehicles and the heat engine has the only function to extend the mile or kilometre range of the vehicle. The range can be for around 100km or simply just 10km. In reality, for a full charge, a lot of gasoline is not needed ; it is also possible to use a mixes of bioethanol. This method of recharging he batteries “on board” allows the user to use the vehicle for very long journeys which today is something not possible to do on a pure electric vehicle, and also because of the lack of electric charging stations which are needed not only on normal circumstances but also in emercency.

V2G stands for Vehicle to Grid Technology, best known as technology from the vehicle to the network. This technology allows to connect the vehicle to the house ‘s electricity grid and use the vehicle’s electricity for appliances. With a specific software, this system can become a powerbank for the house, reducing energy consumption and keeping the house bill low. It can also be very usefull in case of a black out. This system transforms the vehicle into an electrical generator even when we are away from home.

8

RE FE

SMILE Data Sheet Vehicle Type Dimensions Weight

SMILE The electric Minicar The vehicle “Smile” is a minicar and it’s the smallest vehcile of the I’M green Vehicles range. Although Its size the vehicle has a big compartment, easy to access, thanks to Its back boot.

Quadricycle Minicar 123cm x 182cm x 190cm Lunghezza max 210cm 1100kg

Engine Power

Full Electric

Maximum Power

8,3kW

Battery Pack

4kWh Lib

Slope max

18%

Range FE

70km (gel) 110km (litio)

Speed max Front Breaks Back Breaks

45km/h Disk Tambour

4W

LOGO VERSIONS

MINI SMILE Version

SMILE Interiors

9

minicarconcept

Logo

SMART SMILE Description Smart Smile is the new version of the Mini Smile. It is a fully electric lightweight minicar which has been subjected to a partial restyling. The bumper has been modified to give it a more aggressive appearance to appeal to young people, while a boot has been introduced at the rear of the vehicle.

Boot View

Lights View

Perspective View

Dimensions View

SMART SMILE DIMENSIONS 183cm 183cm

10

185cm

MINI SMILE Mini Smile is a shorter version of the Smile.

RE FE

DATI Sheet Mini Smile Dimensions: x 123cm x 122cm x 193cm Weight: 180kg

N° 1 Smile per l’AMIAT di Torino

n°3 Smile per KOMOP, Croazia

n° 2 Smile per Parco Nazionale della SELVA BOEMA

n° 27 Smile per Progetto MI MUOVO ELETTRICO-FREE CARBON CITY Emilia Romagna

11

RE FE

ECOMILE Data Sheet Vehicle Type Dimensions Weight Engine Power

ECOMILE The Working Vehicle

N1 245cm x 156cm x 228cm 2160kg Full Electric 19KW

Maximum Power

28kW

Battery Pack

96V

Slope max

18%

Range FE

120km (litio)

Speed max

80km/h

Front Breaks Back Breaks

Disk Tambour

The Ecomile vehicle is a van with many cargo systems. It can travel on urban and suburban roads. The vehicle is equipped with a Full Electric or a Range Extended kit.

LOGO VERSIONS

ECOMILE Interiors ECOMILE With Out CARGO BED

12

TECHNICAL DATA

FIAT DOBLO’ BI-MODE FIAT DOBLO’ BI-MODAL BI-MODAL KIT

BM RE FE

Vehicle Type

N1

Capacity

8kWh

Battery Type

FE + Comb.engine

RE

PERFORMANCE Speed max

80km/h

Slope max

18%

Charging Time

4/6 ore

Range FE

50km *

ENGINE

* Possibility to Increase the range.

The hybrid version allows the user to have a completly indipendent vehicle when driving outside the city and in ristricted traffic areas. When entering a restricted traffic area it is possible to switch from the internal combustion engine to the full electric engine using the SWITCH comand o the vehicle control panel.

Power

15kW

Maximum Power

30Kw

Inverter

In270 V 350 A

Tension

12 V

Converter DC/DC

CP3 6000W

BI MODE kit di trasformazione bimodale per minbus

RE FE BM

La nuova frontiera dell’ibrido. con i kit di trasformazione hai un veicolo ibrido allo stesso prezzo e con la stessa autonomia di un veicolo a diesel tradizionale.

IVECO DAILY BI-MODAL Data Sheet KIT BI-MODAL With the Bimodal kit it is possible to have a hybrid vehicle, equipped with both electric and combution engine, at the same price and km range of a traditional diesel engine vehicle. The internal combustion ngine, will be used only when necessary.

* Possibility to Increase the range.

TECHNICAL DATA Vehicle Type

M3

Battery Type Capacity

Il pannello di controllo del BI’MODE può essere installato sia in un nuovo sistema da affiancare al tradizionale computer di bordo ma può anche ENGINE essere integrato a quest’utlimo grazie ad un software di gestione dedicato Power Potenza nominale

30kW

Lithium Battery

Maximum Power Potenza effettiva

60Kw

150Ah/h

Regime

2500-5000rpm

Coppia max

260Nm

PERFORMANCE

FE

Speed max

80km/h

Inverter

In270 V 350 A

Tension Tensione nominale

12 V

Slope max

18%

Converter DC/DC

CP3 6000W

Charging Time Range FE

6/8 ore 100km *

13

500 FULL ELECTRIC DATA SHEET FULL ELECTRIC/RANGE EXTENDED KIT

TECHNICAL DATA Vehicle Type

N1

Electric Engine

Alternating current three-phase asynchronous 30W

FE

Power Maximum Power Battery Pack

The Range extender technology has the same advantages of a Hybrid vehicle in efficency terms but only using a Full electric vehicle.

60W 20Wh a litio

RE FE

PERFORMANCE Slope max

18%

Speed max

80km/h

Charging Time

4 ore

Weight

400kg

Range Full Electric

50 Km *

Hybrid Range

70 Km

* Possibility to Increase the range.

RE FE BM

TECHNICAL DATA Vehicle Type

M3

Electric Engine

BIMODE

Power Maximum Power Battery Pack Seats Weight

60kW 90kW 27kWh 10/20 4500/6100 Kg

PERFORMANCE

FIAT MINIBUS DUCATO BI-MODAL BI-MODAL KIT The hybrid version allows the user to have a completly indipendent vehicle when driving outside the city and in ristricted traffic areas. When entering a restricted traffic area it is possible to switch from the internal combustion engine to the full electric engine using the SWITCH comand o the vehicle control panel.

Slope max

18%

Speed max

80km/h

Charging Time

4/6 ore

Range Full Electric

50/60 Km *

Hybrid Range

600 Km

* Possibility to Increase the range.

14

MERCEDES SPRINT. FULL ELECTRIC KIT

TECHNICAL DATA Vehicle Type

M3

Electric Engine

Full Electric

Power Maximum Power Battery Pack Seats Weight

FE

RE FE BM

60kW 90kW 27kWh 10/20 4500/6100 Kg

PERFORMANCE Slope max

18%

Speed max

80km/h

Charging Time

4/6 ore

Range Full Electric

90/120 Km *

* Possibility to Increase the range.

I’M Green Vehicles company works. N° 1 Jolly per AMSA, Milano

N° 1 Jolly 2000 per Aereoporto Bruxelles

N° 22 Jolly per Medi Ambient, Barcellona

15

TECHNICAL DATA

CHARGING POINT The charging Point is a product which allows the user to recharge an electric vehicle. This device is not meant for any other purpose.

Door Closed View

Dimensions

398mm x 1295mm x 277mm

Work tension

120-230 Vac

Weight

44Kg

Frequency

50Hz

Corrent

40A

Case Protection

IP65

CHARGING PLUG Tension supply

120-230V

Current supply

Single phase

Maximum Current

16A

Socket Type

2P+T+1AUX

The charging point structure is made of stainless steel and plexiglass. The structure is resistant and electricaly insulated. The electronic wiring is protected by an IP65 container which garantees protection rom rain and any other atmospheric agent so that the item can be installed outside. The fundamental components for the correct operation of the Charging Point. 1- Two SCAME PLUGS for charging the vehicle. 2- The comand that unhooks the charging point from electricity in case o emergency. 3- The led light which warns that the charging point is supplying electricity. 4-OPTIONAL: A display panel for the visualization of the charging point status.

16

I’M Green Vehicles company works. N° 26 Ecomile per l’AMA di Roma

N° 6 Ecomile per Medi Ambient, Barcellona

n°1 Ducato Minibus per Comune Sant’Agata di Puglia

17

I-HOME Company Presentation I HOME is a company operating in the Energy efficiency sector tank to the production and the selling of storage systems. The company mission is to combine the storage and the domotic technology with a focus on home electric systems and on the home consumption.

18

PV Devices

120 INFINITY 500

DIMENSIONS AND WEIGHT Battery

210x150x53 mm; 1.5 kg

Pannel

1155x29x26 mm; 1.6 kg

DATASHEET Battery capacity

120Wh-12V / 10Ah

Pannel capacity

28W

OUTPUT Sockets

1x 5V/ 2.1A (USB) 1x 12V/ 5A (DC) 1x 220V/90W (AC) 3-4h

Charging Time

How To Use Your INFINITY

BATTERY DURABILITY AND CHARGING DEVICES DEVICES

GPS Cellular Phone Smartphone Led Light Eco Save Bulb HI-FI Notebook Freezer Fridge Computer Tape Recorder Television Classic Light Bulb

WATTS

HOURS

7 7 10 1.5 20 30 40 50 50 70 80 100 100

17 17 12 80 6 4 3 2.4 2.4 1.7 1.5 1.3 1.3

50

1

Using electric current with the appropriate power supply which comes together with the INFINITY 120.

2

Threw the solar panel 28.

2 1 KIT

28 Pannello Fotovoltaico pieghevole

CONVERTITORE AC/AC 220/110V

ER BULBS Kit 5 Lampade 12V - 3W/cad con accensioni separate

Available also the Infinity 50Wh Dimensions (mm) 120x75x20 Weight (kg) 0,350 Input Micro USB 5 Vdc - 1000 mA Max Output USB output 5 Vdc - 1000 mA Max USB output 5 Vdc - 2100 mA Max

Internal Components Battery Li-Ion Battery capacity 50 Wh - 13000 mAh Lifetime (n° di cicli) Approx. 800-1000 Class III Charging Time ~10 h

19

SOLAR POWER STATION

THE ENERGY YOU NEED

INFINITY 500

DIMENSIONS AND WEIGHT Battery

255x210x235 mm; 9.2 kg

Pannel

992x850x36 mm; 11 kg

DATASHEET Battery capacity

512 Wh-40V / 12.8 Ah

Pannel capacity

120W

OUTPUT Sockets

2x 12V/ 5A (DC) 1x 12V/ 7A 2x 5V/ 2.1A (USB)

INFINITY 500 is planned to supply electric current to stands, isolated cabins, gazebo and can light the environment and recharge many electric devices like tv, notebook, tablet and many more.

BATTERY DURABILITY AND CHARGING DEVICES DEVICES

GPS Cellular Phone Smartphone Led Light Eco Save Bulb HI-FI Notebook Freezer Fridge Computer Tape Recorder Television Classic Light Bulb

WATTS

HOURS

7 7 10 1.5 20 30 40 50 50 70 80 100 100

72 72 50 334 25 17 12 10 10 7 7 5 5

350 Available also the Infinity 350 lead gel with 350 Wh

20

2x 220V/ 300W (AC) 3h

Charging Time

How To Use Your INFINITY

1 Using electric current with the appropriate

power supply which comes together with the INFINITY 500.

2 Threw the solar panel 120.

2 1 OPTIONAL

ER BULBS Kit 5 Lamps 12V-3W/cad

120 Solar Panel

CONVERTITORE AC/DC 220V/ 110V

CONFURTABLE BAG to carry the ER 500

E-BOX

DIMENSIONS AND WEIGHT Battery

350x210x235 mm; 25 kg

Pannel

1200x850x36 mm; 3 kg

DATASHEET Battery capacity

1kW

Pannel capacity

750W

OUTPUT Sockets

2x photovoltaic plugs 1x 24V/ 7A 2x 5V/ 2.1A (USB) 2x 220V/ 300W (AC)

WATTS

4h

Sorage

IP66

HOW TO USE THE E-BOX

Visual Visual E-Box E-Box Parts Parts

BATTERY DURABILITY AND CHARGING DEVICES DEVICES

Charging Time

HOURS

140 7 GPS 140 7 Cellular Phone 1kW 100 10 Smartphone 512 1.5 Led Light Display Display di controllo di controllo Connettori Connettori fotovoltaici fotovoltaici e uscita e uscita 220V 220V 50 20 Eco Save Bulb 32 30 HI-FI 24 40 Notebook Display di controllo Connettori fotovoltaici e uscita 220V 20 50 Freezer 20 50 Fridge 14 70 Computer 14 80 Tape Recorder 10 100 Television 10 Classic Light Bulb 100

1kW

Visual E-Box Parts

OPTIONAL 1-Display Rasberry view. 2-24V e USB socket view. 3-Switch view. 4-220 V and PV sockets view. 5-Ebox with panel. Vista Vista ampia componenti componenti elettrici elettrici 1ampia

Vista ampia componenti elettrici

E-BOX is a storage system that allows you to accumulate the energy deriving it from PV panels. This energy can be used to recharge the home electric devices (es. TV, appliances, lights, ecc). 2 Smartphone, tablets and other devices can be Vista Vista Storage Storage concon Modulo Modulo FV Pieghevole FV Pieghevole Vista Vista uscite uscite USBUSB e 12V e 12V reload thanks to the USB connectors. The system Vista Storage con Modulo FV Pieghevole Vista Interruttori Vista uscite USB e 12V is an IP66 storage and is planned on a trolley.

Visual E-Box Parts

Visual E-Box Parts 3

Connettori fotovoltaici e uscita 220V

Display di controllo

Vista Vista Interruttori Interruttori

Vista ampia

4

Connettori fotovoltaici e uscita 220V

5

Display di controllo

21

Vista Storage con Modulo FV Pieghevole

Vista uscite U

SOLAR LIGHT KIT 3 LED Lamps 1.8W

ER-LIGHT DATASHEET Solar Panel

7.5W; 310x195x19mm; 0.6Kg

Lamps

3 LED 1.8W lamps each.

Battery

1 Integrated lithium Battery 2600mAh each

Light Intensity

200 lumen-5 h

Charging Time

4-5 h

ER LIGHT can light small flats, gazebo, sheds (cabins) stalls, vinery vans, closets, thanks to the sun. During the day you reload the lamps and you have the light in the night.

SOLAR LIGHT KIT + 2 LED Lamps 3W+ USB Cable The kit includes: -Photovoltaic panel; -2 LED bulbs with built-in batteries, shutdown button, hook; -Multiplug Connector; -3 Cables 5mt with snap connectors; -Remote control; -Adattatore USB power strip for portable devices; -2 fairleads for suspension lamps;

There are two light points, manageable by remote control. It has the ability to adjust the light intensity in three different degrees depending on the actual needs. This allows to better observe the battery. Thanks to the USB adapters, ER LIGHT can also recharge your smartphone.

22

ER LIGHT + DATASHEET Solar Panel

9W; 270x270x18mm; 0.6Kg

Lamps

3 LED 1.8W lamps each.

Battery

1 Integrated lithium Battery 2600mAh each

Light Intensity

100% 300 lumen- 3h 50% 150 lumen- 6h 10% 30 lumen- 30h

Charging Time

4-5 h

Tempo di ricarica

PV Structures

23

SOLAR GENERATOR CONTAINER DA 100 kWh

PV STRUCTURE Power

20kW

Polycristalline PV

90 polycristalline 240W panels for a total of 21,6kW peak power

Output

400

Structure

6 alluminium structures 5 x 5m with steel joints

Connectors

Standard fast MC4/Tyco with rail connection

Daily Output

100kWh

Vac 50/60 Hz

The power station is already installed and ready to use, with two three-phase 400 VAC electrical outlets. Thanks to the snap in – mounting, both of the external structure of the solar panels, ER GENERATOR can be installed in a short time. The generator provides 100 kWh of energy storage through prewired tubular batteries with electrolyte gel, to reach up to 24 hours. It can generate high peak power up to 40 kW, for total energy autonomy in avery area of the world. Thanks to a double set of photovoltaic inverters, high efficiency polycrystalline panels, container IP67 and OPZV batteries (with more than 3.000 charge and discharge cycles), it is possible to reach ten years of use without any need for maintenance, making only simple control operations and cleaning.

INVERTER

STORAGE

Max Power

20kW

Total Energy

100kWh

Max Voltage Input

1000Vcc

Battery

Batteries with no maintenance

Voltage

2V

Open Circuit Voltage Range

300-800 Vcc

MPPT Temperature Range Performance

24

-20+60°C 98%

Battery Cell Capacity

250Ah

Cicles 100%80%50%

1.700/2.100/3.300

Container

Standard Alley container 20?, IP67

Plugn’Play

All the electronics are ready to use

SOLAR CARPORT Description -The structure supports any PV panel size; -On requests, the solar carport can be equipped with a gutter; -The cover is modular and is suitable for parking of any size; -The asset allows a perfect balance and high resistances to the stresses caused by snow and wind. Warranty: 15 years. -The structures is composed of profiles in silver anodized aluminum and stainless steel joints.

Technical Data SOLAR CARPORT A solar carport structure can cover many parking spots until the max length of 600 cm. In these imagines you can see many versions, where it is shown the number of photovoltaic panels that can be installed in a horizontal orientation. ACCESSORI: CONTROSOFFITTO IN LAMIERA VERNICIATA

- Protezione cablaggi - Perfetta tenuta all’acqua piovana

ACCESSORI: CONTROSOFFITTO ACCESSORI:CONTROSOFFITTO CONTROSOFFITTO ACCESSORI: IN LAMIERA VERNICIATA INLAMIERA LAMIERAVERNICIATA VERNICIATA IN

- Protezione cablaggi Protezionecablaggi cablaggi - -Protezione - Perfetta tenuta all’acqua Perfettatenuta tenutaall’acqua all’acqua - -Perfetta piovana piovana piovana

DETTAGLI TECNICI

DETTAGLI TECNICI

ACCESSORI PANNELLI RIGIDI PUBBLICITARI

DETTAGLI TECNICI

The structure has successfully passed the load test in which it was subjected, reacting to the maximum loadTECNICI required by the static calculations with no permaDETTAGLI nent deformation. Each beam weighed for four day two 200 Kg weigh, exerting maximum effort on the structure joints.

ACCESSO ACCESSORI ACCESSORI PANNELLI RIGIDI PU PANNELLI RIGIDI PUBB PANNELLI RIGIDI PUBB

The Customize PV Shelter

Joining Components -Reinforced concrete fixing structure. -Bracket + 2 pickets for hard grounds. -Bracket + 4 pickets for hard grounds. -Bracket + 6 pickets for hard grounds. Staffa di ancoraggio per cemento armato

Staffa di ancoraggio da n. 2 picchetti cad. per terreni compatti

Staffa di ancoraggio da n. 4 picchetti cad. per terreni compatti

Staffa di ancoraggio da n. 6 picchetti cad. per terreni compatti

Staffa ancoraggio Staffa di di ancoraggio Staffa di ancoraggio per cemento armato per cemento armato per cemento armato

Staffa ancoraggio Staffa didiancoraggio Staffa di ancoraggio picchetti cad.cad. dada n.n. 2 2picchetti cad. da n. 2 picchetti per terreni compatti per terreni compatti per terreni compatti

Staffa ancoraggio Staffa didiancoraggio Staffa di ancoraggio dan.n. picchetti cad.cad. da 44picchetti cad. da n. 4 picchetti perterreni terreni compatti per compatti per terreni compatti

25

d

TECHNICAL DATA SOLAR ROAD LAMP The photovoltaic lamp post comes with: - 1 crystalline PV module; - Charging controller that manages the solar power production during day and the on / off / dimming of the lamp during the night; - Lead Batteries without maintenance; - Steel head pole holder with built-in battery compartment to the rear opening with a fixed tilt; - Intelligent LED lamp; - Lamp arm Holder; - Pole (OPTIONAL) The post is designed to work up to 12 hours per night (with the possibility of working at reduced luminous flux of the battery charge function) with an autonomy in poor insolation conditions.

CHARGING CONTROLLER

SOLAR ROAD LAMP DESCRIPTION The photovoltaic lamp includes: -MPPT Charge controller that manages the battery with solar energy produced during the day and the on/off/ dimming of the night streetlight; -Wide input voltage range of the photovoltaic module (up to 100V); -Max power of the PV panel 225W, 12V ; 450W; 24V -Integrated blocking diode; -Auto-detect of 12V or 24V -Switch for selecting the battery type: hermetic of free acid; -Switch for the selection of battery distance 1mt or 10mt; -Integrated light sensor (via PV module); -Management of the activation of the lead with flow reduction; -Self management of the power –on hours; -Anti-reverse battery protection; -Low-battery protection -Overload and over temperature protection; -IP66 storage for outdoor use -Electric Cables

26

WATER Treatment Products

27

Technical Data

Water Species Acqua dolce

0-1.000

Acqua salmastra

1.000-5.000

Acqua moderatamente salina

5.000-10.000

Acqua altamente salina Acqua marina

10.000-30.000 30.000

Advantages Dissalinating Container The Desalinating water treatment of sea water and brackish water is a process that reduces the presence of organic, inorganic components and the salt in the water. Ships, islands and coast areas of certain countries require the application of desalination tecniques in order to create drinkable water.

DESALINATION Kit • • • • • • • •

Sea Water supply system. Microbial Pre-Treatment Activated carbon filtration Further Microbial Pre-Treatment Ultrafiltration Bacteria reduction Dosing station Reverse Osmosis

28

- Energy consumes reduced thanks to the special membranes, that are able to work on low pressures, and to the inverter for the pipe pressure modulation. - Energy saving and minor costs are garanteed. - Accurate Monitoring and Plant automation. - The system Operating Parameters are monitored in remote and local master. - Energy recovery system. The plants may be accompanied with a system of energy recovering in order to decrease energy consumption up to 70%. - Salt reduction acording to potable water standards by the OMS. - Automatic Switch from Bi-Osmosis to Mono-Osmosis. - Reduced space volume.

Drinkable Water Kit The drinkable water treatment system of brackish water from supplying sources, fountains and aqueduct ecc is based on the membrane filtration function. The vessels can accommodate ultrafiltration membranes and reverse osmosis membranes acording to the “multibarriera” (multi lateral barriers) approach. The use of different filtration membranes grantees a high flexibility of the plant so that it can respond to different treatments. Installed on a cargo trailer the plant is conformed in order to be moved on any type of road and it is provvided with an electrical generator. The plant is meant for: - Crude Water extraction. - Crude Water obtaining.

-

Chlorination department. 90 μm filtration. Adsorption activated carbon. Micro Filtration. Ultra Filtration. Product dosage. Reverse Osmosis filtration. Treated water Accumulation. Disinfection.

WATER ULTRAFILTRATION KIT The drinkable water treatment system of brackish water from supplying sources, fountains and aqueduct ecc is based on the membrane filtration function. The vessels can accommodate ultrafiltration membranes and reverse osmosis membranes acording to the “multibarriera” (multi lateral barriers)approach. The product comes in a 20 foot long container and the plant is easy to transport and can be mounted on to any flat surface. The plant is meant for: - Sedimentation - Crude Water treatment. - 90 μm filtration.

-

Column filtration. Safe Filtration, 5 μm Flushing and cleaning system (Cleaning in Place) Treated Water accumulation.

PROBLEM SOLUTION -Murkiness. -Sand. -Organic compost and chlorinated. -Adsorption activated carbon. -Iron and magnesium. -Iron reduction. -Arsenic. -Arsenic reduction.

29

Water is essential in our life time but it can be also contagious in certain circunstances. Water quality laws are different in some countries and the OMS (Health World Organization). The European Union acording to the OMS has stated a document which underlines the minimum requirements for potable water. So it is stated that water is not potable if it containes: - Metals. - Arsenic, antimony, boron and selenium. - Toxic organic material ( Organohalogen material, benzene, trihalomethanes, ecc) To answer to the water consumption needs, special plants have been designed based on reverse osmosis technology, making sure of keeping the maintenance costs, the energy consumption and the loss of energy level.

iIn order to have potable water it is not always necessary to use a filter whith an appropriate filtering tool. Sometimes it is necessary to use advanced technologies on the market in emergency situations or after natural disasters. The reverse osmosis plants, are suitable in many ways for water potabilization. The advantage are: - Riducted Energy consumes. Thanks to the use of special membranes which are able to work at low pressiures, to inverters which control the pump pressures, energy saving, and cost reductions garanteded. - Accurate monitoring and plant automation. The operating parameters are controlled on the management controlling remote panel.

It is possible to set a threshold which predicts a series of automatic operations including sending the system in block. - Microbiologial parameter, chemical and radioactive fulfillment. - Plant security. - Automatic transfer from bi-osmosis to mono-osmosis. - Collecting pipes in PVDF material. - Space capacity reduction.

POTABLE WATER KIT Reverse osmosis plants are entirely assembled on to skid in order to help the carriage and the installation. To ensure maximum reliability and flexibility of the operation, each

30

plant is equipped with: • Activated Carbon Filtration • Filtration micron • Ultrafiltration • UV sterilization • Dosing system antiencrustation

• Reverse Bi-Osmosis • automatic flushing system of membranes • chemical washing of the membranes system

The system provides an automatic and continuous operation; the traceability register allows to control events occurred locally and remotely.

A dialysis patient comes into contact, weekly, with a large quantity of water that, therefore, must respond to high requirements for quality and purity. Specifically, the dialysis fluid must have:

- Proper electrolyte composition. - A low concentration or absence of organic and inorganic chemical micropollutants. - A low concentration or absence of bacteria and endotoxins.

MEDICAL KIT The advantages of the compact systems are: • Certified Medical Device, in accordance with the European Directive 93/42 EEC. The entire process chain, from pretreatment to bi-osmosis, is certified Medical Device • Ultrafiltration. This low-pressure separation process is able to filter viruses, bacteria, sediments and colloidal substances by means of semi-permeable hollow fiber membranes having pores with a diameter between 0.01 and 0.1 microns. Ultrafiltration ensures sanitation of osmotic membranes, extending a 20% of their useful life and increasing its effectiveness. • UV lamp. The UV germicidal lamp guarantees the disinfection of water in the ring return input line osmosis • Automatic switching to bi-osmosis mono-osmosis. • Programmed Turning on and off and easily manageable by PLC. • Collecting pipes made of PVDF • space-saving space.

The system comes complete with: • Pretreatment Micronic • Activated Carbon Filtration • Further filtration micron • Ultrafiltration • UV sterilization • Reverse Bi-osmosis The system provides an automatic and continuous operation; the traceability register allows to control events occurred locally and remotely.

31

Water Treatment Products In Food Industry The water used in food production has to meet high health and safety standards for the protection of consumer health. Water is properly used when there is compliance with the quality parameters established by the regulations in force. In particular, the treatment of the waters process, shall ensure: - The prevention of contamination - The removal of harmful

Water treatment plants are designed in order to meet the needs of the different stages of production of the food industry and beverage industry, in the respect laws of the environment and foods. The advantages are: • Energy savings and lower operating costs. Reduced energy consumption and low costs thanks to the use of special membranes, that work at low pressures, and inverter systems for the modulation of pressurization pumps. • Accurate monitoring and automation system. The system operating parameters are monitored both locally and remotely framework. It is pos-

32

substances such as pathogens (bacteria, phytoplasmas, viruses), pesticide residues, heavy metals, etc. - The satisfaction of organoleptic parameters, microbiological and chemical.

sible to set a threshold value which shall predict a series of automatic operations including the blocking of the system. • Compactness, plant flexibility and easy maintenance. The modularity of the system is well suited in every season of the year. It can also get the HEALTH SOLUTION KIT notice of necessary maintenance directly from the manaThe Directive 98/83 / EC used in food production, requigement controlling panel. which governs the quality of res the application of innovati• Plant safety. water intended for human ve technical solutions, capable consumption, including both for of offering the best results in drinking water as well as those costs competitive.

WATER Products

33

TECHNICAL DESCRIPTION The product produces drinkable water without the need for connection to the water system. STEP 1: Air filtration. The first phase of electrostatic air filtrationremoves dust, the pollens, molds and other contaminated agents suspended in the air that enters ER NEPTUNE. STEP 2: Condensation. The flow of air that enters the machine is cooled and brought to the point of condensation to allow any moisture contained in the air of passing from the gaseous state to the liquid state. STEP 3: Sterilization. After finishing the process of condensation, the water is filtered and stored in a tank in which develops a sterilization process using UV lamps. STEP 4: Purification. Without the use of batteries, water is send into a special filtration system that makes it pure and healthy. STEP 5: Dispensing. With a simple pressure on the panel’s button, it will be possible to have without any effort, potable and tasty water.

TECHNICAL DATA

COSTS COMPARISON

Production: 30 L / day at 28ºC with 80% RH Dimensions: 80 x 60 x 100 cm (solar panel appart) Weight: 39.5 kg + 100 kg (fotovoltaic kit) Tank: 30 L Material: Stainless Steel Power supplier: Sun

Neptune KIT The Potable Water Generator -Performance: producing up to 30 liters of water per day. -Purification water: of a 5-stage filtration process. -Purification air: washable filter for the removal of dust and other airborne particles Storage Capacity: 30 liters total water accumulation. -Electronic sensors: each critical-component of the system is equipped with an electronic sensor that ensures the proper operation and sends an alarm in case of any malfunction. energy -Saving: car of the capacitor being switched off in the event of raggiugimento the maximum water level in the tank in order to both reduce the consume of energy that preserve the battery life. -Multifunzionale: thanks to the air filtration and condensation dell’umitità, thanks to ER NEPTUNE, the air of the room in which it is bound will be more pure and less humid. -Easy maintenance: ER NEPTUNE is designed to be simple and for easy maintenance.

34

COUNTING COSTS Prezzo Kit filtro per 1 anno Ammortamento impianto Kit filtri Kit batterie Water production per year Prezzo al litro

3.700€ (garanzia 10 anni) prezzo netto 200€ incluso PV prezzo netto 370€ prezzo netto 200€ prezzo netto 200€ Totale 770€ 30 litri X 365 GIORNI= 10.950 litri 7cent/litro

3,0

2,8 3,6

TECHNICAL DATA

DATA

WORKING CONDITIONS

OFFICINE DI TREVI Catalogo 2014

• External pump case, delivery head, suction, shaft, impellers and diffusers in stainless steel. • The check valve made of stainless steel is installed inside the delivery head. • Motor coupling meets NEMA standards. • 2 poles asynchronous motor, 50 Hz, 2850 rpm. • Class F insulation. • IP68 protection. • Working voltage: three-phase 400 V

• Pumped liquid: clean water, non aggressive, without solid particles. • The pump can not operate in dry conditions. • Pump body always completely submerged. • Temperature of pumped liquid: min 5°C - max 90°C. • Vertical operating position. • Maximum number of starts per hour: 20.

SOLARE 2 APPLICATIONS Water supply from deep wells, ci-

APPLICAZIONI vil and industrial raising systems, Per il sollevamento dell’acqua rain and running irrigation, da fire fighting systems, aqueducts. pozzi profondi in impianti alimentati da energia solare. CARATTERISTICHE L’innovativo impianto si compone di tre elementi: • i pannelli fotovoltaici (non forniti) • il quadro di regolazione ad inverter • l’elettropompa L’inverter Solare 2 lavora in presenza della tensione fornita daipannelli fotovoltaici, in assenza della quale l’impianto non funziona. Non necessita di batterie d’accumulo per l’energia elettrica in quanto, con questo sistema, l’acqua viene pompata e stoccata durante il giorno, per l’eventuale utilizzo durante la notte. Per un corretto funzionamento l’inverter Solare 2 deve essere alimentato a 320 Vcc o 560 Vcc.

35

DATA . Multistage centrifugal electric submersible pumps for wells. . External pump case, delivery port, suction, motor shaft and others components in stainless steel. . Impellers, diffusers in special technopolymer. . The check valve made of stainless steel is installed inside the delivery head. . The pump is equipped with 30 m of H07RN-F electric cable. . External diameter: max 105 mm.

Kit Solare

3,5

3,0 2,1 2,8

. 2 poles asynchronous motor, 50 Hz, 2850 rpm. . Class F insulation. . IP68 protection. . Working voltage: single-phase 230 V, three-phase 400 V. . The electric motor is cooled by non-toxic, non-polluting liquid.

. Pumped liquid: clean water, non aggressive, without solid particles. . The pump can not operate in dry conditions. . Pump body always completely submerged. . Temperature of pumped liquid: min 5°C - max 30°C. . Vertical operating position. . Maximum immersion depth: 10 m. . Maximum number of starts per hour: 20.

APPLICATIONS Raising of clean water from deep wells and tanks, civil and industrial water raising system, rain and running irrigation, aqueducts.

3,5

3,0

2,8 3,6

TECHNICAL DATA

OFFICINE DI TREVI Catalogo 2014

36

WORKING CONDITIONS

FUNCTION

PERFORMANCE

The Product once is submerge can be ready to use. It has a control panel, a protected engine and a 10 metre cable. It uses non toxic paints, certified to be in contact with edable products and recycable packagings. The product garantees High performances, low energy usage and a 2 year warranty. It can work indipendently using clean and renewable energy from the sun.

No periodic unlocking maintenance of the impeller. High performances. Horizontal and vertical working. Eco-friendly product (non-toxic paints and oils, recyclable packaging).

USE Submersible pumps for clean water pumping from wells, cisterns and storage tanks. The pumps is long-life designed and is fully provided with control panel and built-in capacitor and thermal motor protection.

ECOFRIENDLY Stand-alone photovoltaic system for water pumping stations. Ecosolar P60 converts solar energy obtained from photovoltaic panels, into 230 Volts alternating current. The unused energy is stored in batteries. Unlike conventional inverter systems, which regulate motor speed according to irradiation available, Ecosolar P60, thanks to electric batteries, guarantees the operation of the electric pump at the highest regimes, even in the total absence of sunlight. Ecosolar P60 is also an electric power supply system in case of emergency, in fact, it is designed to be connected to the electrical network. In this way the system uses the current network as a priority, but during blackouts it uses the energy of the panels and batteries, ensuring the operation of the electric pump. Safe and reliable, it can be used to power any users at 230 Volts, with compatible power. The LCD display makes it intuitive and easy to use.

USE It’s designed for both continuous and intermittent working, it’s particularly suitable for all installation in remote locations and for applications such as irrigation of fields and greenhouses, watering animals and pressurization generally.

PERFORMANCE -Max Flow rate: 20 m³/day -Max Head: 62 m (6,08 bar)

37

PV Products

38

TECHNICAL DATA

POLICRYSTALLINE 72CELLS

The solar cells used in our modules offer an high conversion efficiency of the sunlight. These property guarantee high yields. Our solar modules have only positive power tolerance of 0 + 5 W. These pledge a more stable production. The modules resist at the worst meteorological conditions and at extreme temperature

APPLICATIONS All Waris solar modules are optimazed for every type of PV system, from residential to industrial and PV plant.

WARRANTY Waris solar modules have a 12 years on product defects and a linear power output warranty: •97% towards the nominal power* during the first life year and afterwards a maximum degradation not up at an annual 0,6% •92% towards the nominal power* within the first 10 years from the purchase •85% towards the nominal power* between the 11th and the 20th year from the purchase •83% towards the nominal power* between the 21st and the 25th year from the purchase

MONOCRYSTALLINe 72CELLS

TECHNICAL DATA The modules FS Series 2 and Series 3 thin film highly developed technology based on CdTe are distinguished by high efficiency even in different climatic conditions. The modules have an extraordinary performance even with low irradiation and a high temperature coefficient. The modules provide verifiably advance the calculated yields coeffieciente with a very high performance. Frameless laminate is very durable, efficient, inexpensive and recyclable. The production is carried out in modern factories are mainly automated that are certified according to the ISO 9001 (quality) and ISO 14001 (environmental management). The modules are independently tested by leading European and American institutions and reliability and safety certificates.

APPLICATIONS The photovoltaic modules of the series 2 and 3 are tested to a voltage of 1000 VDC limit and certified in accordance with IEC 61646 and Class II. First Solar provides the leaders in the field of photovoltaic project developers and system solutions in the integration of thin films at low cost for photovoltaic systems connected to large network. Their application engineers are able to offer comprehensive technical assistance, and to provide a detailed technical documentation to support the design, installation and long-term use of photovoltaic systems with high efficiency.

WARRANTY The warranty for defects in materials and production is five (5) years. The power rating (Pmpp +/- 5%) during the first ten (10) years is 90% and 80% during twenty-five (25) years, subject to the conditions and terms of guarantee. The management of the lifecycle of the modules provides a pre-funded retirement and recycling program, which guarantees the owner the withdrawal and Free module recycling at the end of their lifespan.

39

Technical Data

Mechanical Data Temperature –40° C to +85° C Impact resistence Hailstorm diameter 25 mm each speed of 23 m/s A class Solar cells 96 monocrystalline cells Maxeon of II generation Tempered Glass of high transmission Container IP-65, Yukita (YS-254/YS-255) Weight 18,6 kg Maximum load Wind: 2400 Pa, 244 kg/m² front and back Snow: 5400 Pa, 550 kg/m² front Black Alluminium frame

Electrical Data

During the first year the panel will increase the energy production around 7-9% of what it normaly produces. This advantage will increase in time, reaching up to further 20% of energy for the next 25 years.

Power (Pnom) 11 333 W Power Tolerance +5/–0% Media Module efficiency12 20,5% Power Tension (Vmpp) 54,7 V Maximum current power (Impp) 6,09 A Open circuit current (Voc) 65,3 V Short circuit current (Isc) 6,46 A Max system Tension 1000 V IEC & 600 V UL Max fuse current 15 A Coeff. temp. power –0,38% / o C Coeff. temp. tension –176,6 mV / o C Coeff. temp. current 3,5 mA / o C

Electrical Data Test standard13 IEC 61215, IEC 61730, UL 1703 (fire resistent) Quality test ISO 9001:2008, ISO 14001:2004 Compliance EHS RoHS, OHSAS 18001:2007, no lead, PV Cycle, REACH SVHC-163 Environmental Compatibility Cradle to Cradle Ammonia test IEC 62716 Resistance test sand storms 10.1109/PVSC.2013.6744437 Resistance test to salty water IEC 61701 (max level) Test PID Absence of degradation induced by voltage: 1000 V9

-Policrystalline cells 72 / 6 x 12 -Efficiency 16% -IP 65 -Alluminium Frame

40

Technical Data Data INPUT Max Power

2100W

Max Voltage

170V-400V/380

Voltage range

80V/110V

Current input max

14A

Number of inputs MPP

1/1

Max Voltage input

1.000 V

Gamma Tension

MPP 580-850 V

Number of MPP

1

Number of inputs

CC 6

OUTPUT data Power

SAM INVERTER - Free site selection due to IP65 - Easy installation and maintenance due to “Plug & Play” connection - Interface selection-Ethernet,Wi-Fi and RS485 for more flexible configuration and system monitoring - Multi-lingual 2-line LCD display - Digital inputs for the economic connection of a ripple control receiver. - Configurable multi-function replay output. - Highest earnings through max.efficiency of 96.8% - Safe operation due to integrated DC-switch - No Fan design for low failure rate and longevity. - Sturdy design due to High Accelerated Life Testing(HALT) and rigorous Multiple Environmental Over Stress Testing (MEOST). - Defeating shade effect by Global Peak Tracker

CA Power max

25.000 W 25.000 VA

CA Voltage Voltage CA range

220V/230V/240V 180V/277V

Frequency CA Network power Voltage

50Hz/60Hz 230V/50Hz

Current max. exit

9.1A

Power Factor

1

Factor Range Power

0,90

Imission fase/connection fase

1/1

Range Max Range/ European range

96.8%/96.2%

Technical Data

DOTAZIONE

Dimension

333x425x147mm

Connessione CC/CA

MC4,H4,SUNCLIX/ spina

Weight

13,7kg

Protection Grade

IP65

Display

LCD a due righe

Topology

Interfacce

RS485/WLAN/ ETHERNET

Noise

With out Transformer